Saniflo SaniBEST | Macerating Upflush Toilet Kit

Description: This SaniBEST Upflush Kit IncludesThe SaniBEST macerating bathroom pumpWhite toilet bowl (size: standard)White toilet tankExtension pipe (for behind the wall installation)Retail Price: $1,764.00Our Price: $1,499.40 + no tax + free shipping (20-30% total savings)UPC#s 013, 083, 005,030Available Product Combinations BOWL SIZEEXTENSION?RETAIL PRICEOUR PRICESAVINGSBUY HERE:Combo 1Standard BowlNo Extension$1,704.00$1,448.4020-30%click here Combo 2Standard BowlPlus Extension$1,764.00$1,499.4020-30%this listing! Combo 3Elongated BowlNo Extension$1,748.00$1,485.4020-30%click here Combo 4Elongated BowlPlus Extension$1,808.00$1,536.4020-30%click here SaniBEST Benefits The SaniBEST is a system that is used to install a complete bathroom up to 15 feet below the sewer line, or even up to 150 feet away from a soil stack. The SaniBEST pump is designed to connect with:This SaniBEST Upflush ToiletAny SinkAny ShowerAny BathSaniBEST Installation The SaniBEST is simplicity itself to install; there are just four connections.The macerating/pump is connected to the spigot of a horizontal outlet toilet. The toilet tank is connected to the water supply. The macerating/pump is connected to the small diameter discharge pipe work. The macerating/pump is connected to the electrical supply. Then optionally connect the discharge pipes from the sink, shower and/or bath.SaniBEST Function The inside of the SaniBEST is comprised of a pressure chamber, which starts and stops the unit, and the motor, which drives the stainless steel cutting blade and the pump. When the flush is activated, the water flowing into the SaniBEST activates a micro switch in the pressure chamber, which in turn starts the motor. The motor is sealed for life in an oil filled enclosure. A common spindle/shaft drives the impeller and the blades. The moving parts therefore are kept to an absolute minimum. Water and organic waste matter, enter the chamber and are reduced to slurry as the blades rotate at 3600 RPM. The reduced solids are picked up at the bottom and the impeller mounted beneath the motor ejects the waste. The unit pumps the effluent upward to 18 feet and/or 150 feet horizontally (with gravity fall). Once the water level in the container goes down, the micro switch deactivates. A normal operating cycle for the SaniBEST takes about 7-9 seconds depending upon the discharge pipe run configuration. In addition, the SaniBEST will also discharge gray water from a variety of other sanitary fixtures such as: a sink, a bath/shower, a urinal and even a washing machine (indirect connection). When adding a bathtub/shower, a base will have to be constructed. This base should be made out of a 2” x 6” (minimum) or 2”x 8” (recommended) on edge, to allow for the installation of a P-trap and the required 1/4” per foot gravity flow towards the pump unit. The wastewater from other sanitary fixtures is discharged into the SaniBEST via two 1½-inch inlets on either side of the housing. The discharge elbow on top of the SaniBEST can be rotated 360 degrees depending on the discharge installation. A non-return valve (included in assembly) prevents back flow into the unit. This unit has been designed with a vent connection on the lid. All plumbing codes require connection to a vent system. Please note that the vent system should be a two-way air vent. The use of mechanical vents, air admittance valves or similar devices are not permitted as these are considered one-way air vent systems. The SaniBEST unit must be connected to our rear discharge toilet. It is highly recommended for the grinder to be connected to a Ground Fault Interrupter (GFI) circuit. The Sanibest has been certified to American and Canadian Standards. Macerating standard; US: CSA Certified & IAPMO (UPC) listed - ASME A112.3.4, CA: Macerating Standard CSA B45.9. SaniBEST Water Conservation The water closet the SaniBEST is connected to, uses much less water than a regular toilet, it uses 6 liters (1.6 US Gal) of water per flush.SaniBEST Product Specifications PART NUMBERS UPC#s 013, 003 and 005 UPC# 030 (Extension) DIMENSIONS (PUMP ONLY) H10" x W21" x D9" H26cm x W53cm x D23cm MOTOR Induction Motor No carbon brushes or gears. Tested over 30,000 cycles. 3600 rpm. ELECTRICAL SUPPLY 110-115V; 60Hz; 15 Amps Usage 9 Amps DISCHARGE Horizontally to 150 ft (50m) Gravity Fall on Horizontal installations: 1/4" per ft Pumps vertically to 18 ft (5.5m) DISCHARGE PIPE DIAMETER 3/4" 21mm CONSTRUCTION MATERIALS Polypropylene, C.R.P., Stainless Steel, Neoprene MAX TEMPERATURE 104°F 40°C NORMAL RUNNING TIME 7–9 secs subject to installation pipe run WATER PER FLUSH 1.6 US gal 6 liters VOLUME 7.35 gal/m 27 l/m OptionsBowl Size REGULAR ELONGATEDBOWLRound FrontElongated FrontTANKVitreous china tankVitreous china tankHEIGHT (SEAT)16-3/4 inches16-3/4 inchesDEPTH (OVERALL) 26-1/2 inches28-1/2 inchesVOLUME1.28 gpf1.28 gpfWARRANTY1 year on china1 year on chinaADA COMPLIANTNoYesExtension INSTALLATION - Visible INSTALLATION - Behind WallEXTENSION PIPE NEEDED? NoYesShippingSame day order processingSame day shipping Shipping via UPS, tracking number providedShip to contiguous USA, no PO BoxesPaymentPaypal, Credit CardsReturnsWithin 30 days, unopened, resalable packages; Buyer pays return shipping.Customer SupportFull phone support is provided to all our customers. Satisfaction is guaranteed. You'll receive a direct support phone number with your order confirmation email. About UsTop rated, authorized SaniFlo dealerOver 30 years’ experienceNew to eBay, but veteran in online salesWe provide our customers:Full Phone Support2 Year WarrantyContact UsWe have SaniFlo experts waiting and all questions,during business days, are answered within 2 hours! Satisfied customers“We put the SaniBEST in our offices here, and it gets used ALL THE TIME from everyone drinking too much coffee lol. But it works great, no issues, would definitely put another one in.” Greg H. Louisiana“We have had major clogging issues with our other toilets, but this one works great. I've never had a problem with it.” Aaron V. Washington“Got to my house in 3 days. I was shocked! Just top-notch ecommerce site all round. Thank you guys!” Monte H. Alabama This SaniBEST Upflush Kit IncludesThe SaniBEST macerating bathroom pumpWhite toilet bowl (size: standard)White toilet tankExtension pipe (for behind the wall installation)Retail Price: $1,764.00Our Price: $1,510.08 + no tax + free shipping (20-30% total savings)UPC#s 013, 083, 005,030Available Product Combinations SaniBest Standard BowlSaniBest Elongated BowlSaniBest Standard Bowl + ExtensionSaniBest Elongated Bowl + ExtensionSaniBest Standard Bowl + SaniAlarmSaniBest Elongated Bowl + SaniAlarmSaniBest Standard Bowl + Extension + SaniAlarmSaniBest Elongated Bowl + Extension + SaniAlarmSaniBEST BenefitsThe SaniBEST is a system that is used to install a complete bathroom up to 15 feet below the sewer line, or even up to 150 feet away from a soil stack. The SaniBEST pump is designed to connect with:This SaniBEST Upflush ToiletAny SinkAny ShowerAny BathSaniBEST InstallationThe SaniBEST is simplicity itself to install; there are just four connections.The macerating/pump is connected to the spigot of a horizontal outlet toilet. The toilet tank is connected to the water supply. The macerating/pump is connected to the small diameter discharge pipe work. The macerating/pump is connected to the electrical supply. Then optionally connect the discharge pipes from the sink, shower and/or bath.SaniBEST FunctionThe inside of the SaniBEST is comprised of a pressure chamber, which starts and stops the unit, and the motor, which drives the stainless steel cutting blade and the pump. When the flush is activated, the water flowing into the SaniBEST activates a micro switch in the pressure chamber, which in turn starts the motor. The motor is sealed for life in an oil filled enclosure. A common spindle/shaft drives the impeller and the blades. The moving parts therefore are kept to an absolute minimum. Water and organic waste matter, enter the chamber and are reduced to slurry as the blades rotate at 3600 RPM. The reduced solids are picked up at the bottom and the impeller mounted beneath the motor ejects the waste.The unit pumps the effluent upward to 18 feet and/or 150 feet horizontally (with gravity fall). Once the water level in the container goes down, the micro switch deactivates. A normal operating cycle for the SaniBEST takes about 7-9 seconds depending upon the discharge pipe run configuration.In addition, the SaniBEST will also discharge gray water from a variety of other sanitary fixtures such as: a sink, a bath/shower, a urinal and even a washing machine (indirect connection). When adding a bathtub/shower, a base will have to be constructed. This base should be made out of a 2” x 6” (minimum) or 2”x 8” (recommended) on edge, to allow for the installation of a P-trap and the required 1/4” per foot gravity flow towards the pump unit.The wastewater from other sanitary fixtures is discharged into the SaniBEST via two 1½-inch inlets on either side of the housing. The discharge elbow on top of the SaniBEST can be rotated 360 degrees depending on the discharge installation. A non-return valve (included in assembly) prevents back flow into the unit.This unit has been designed with a vent connection on the lid. All plumbing codes require connection to a vent system. Please note that the vent system should be a two-way air vent. The use of mechanical vents, air admittance valves or similar devices are not permitted as these are considered one-way air vent systems.The SaniBEST unit must be connected to our rear discharge toilet. It is highly recommended for the grinder to be connected to a Ground Fault Interrupter (GFI) circuit.The Sanibest has been certified to American and Canadian Standards. Macerating standard; US: CSA Certified & IAPMO (UPC) listed - ASME A112.3.4, CA: Macerating Standard CSA B45.9. SaniBEST Water ConservationThe water closet the SaniBEST is connected to, uses much less water than a regular toilet, it uses 6 liters (1.6 US Gal) of water per flush.SaniBEST Product Specifications PART NUMBERS UPC#s 013, 003 and 005 UPC# 030 (Extension) DIMENSIONS (PUMP ONLY) H10" x W21" x D9" H26cm x W53cm x D23cm MOTOR Induction Motor No carbon brushes or gears. Tested over 30,000 cycles. 3600 rpm. ELECTRICAL SUPPLY 110-115V; 60Hz; 15 Amps Usage 9 Amps DISCHARGE Horizontally to 150 ft (50m) Gravity Fall on Horizontal installations: 1/4" per ft Pumps vertically to 18 ft (5.5m) DISCHARGE PIPE DIAMETER 3/4" 21mm CONSTRUCTION MATERIALS Polypropylene, C.R.P., Stainless Steel, Neoprene MAX TEMPERATURE 104°F 40°C NORMAL RUNNING TIME 7–9 secs subject to installation pipe run WATER PER FLUSH 1.6 US gal 6 liters VOLUME 7.35 gal/m 27 l/m OptionsBowl Size REGULAR ELONGATEDBOWLRound FrontElongated FrontTANKVitreous china tankVitreous china tankHEIGHT (SEAT)16-3/4 inches16-3/4 inchesDEPTH (OVERALL) 26-1/2 inches28-1/2 inchesVOLUME1.28 gpf1.28 gpfWARRANTY1 year on china1 year on chinaADA COMPLIANTNoYesExtension INSTALLATION - Visible INSTALLATION - Behind WallEXTENSION PIPE NEEDED? NoYesAbout UsTop rated, authorized SaniFlo dealerOver 30 years’ experienceWe provide our customers:Full Phone Support4 Year WarrantyContact UsWe have SaniFlo experts waiting and all questions,during business days, are answered within 2 hours! Contact Us!Want to talk to a real person? Just message our Upflush Toilet experts anytime with questionsWe pride ourselves on our superior customer service, so please feel free to ask us anything and we will get back to you. We appreciate your interest in our products and will work hard for your business.WE REPLY TO MOST CUSTOMER INQUIRIES IN LESS THAN 2 HOURS (8AM - 9PM ET). HOW FAST DO YOU SHIP? All orders received before 2pm EST ship the same business day. We provide the fastest shipping possible!WHAT SHIPPING METHODS AND OPTIONS DO YOU OFFER? We exclusively ship with UPS ground shipping. Shipping is included FREE in the purchase price to continental USA states. (UPS will not ship to PO Boxes, so please use a street address.)IS A SIGNATURE REQUIRED FOR DELIVERY? Note that UPS will leave the packages at your door or in a "safe place" as deemed by the delivery driver. If you'd like to request that a signature is mandatory, please contact UPS directly and give them the tracking number provided in your "Shipping Confirmation" email and they will change the delivery instructions to "Signature Required".WHAT ARE YOUR SHIPPING RATES? Shipping to you is included FREE with each order in the continental USA. Only on returns does the buyer pay the shipping charges.WHERE DO YOU SHIP FROM? We ship from upstate New York. Delivery to the east coast and mid west is usually 2 to 3 days, and west coast states 3 to 4 days.I NEED MY ORDER ON A CERTAIN DAY, CAN YOU GUARANTEE DELIVERY? Please note that while more than 90% of our customers receive their orders in 2 to 3 business days, we cannot guarantee a delivery day. Once UPS picks up from our warehouse, the package is entirely in their system and control. Delivery times are dependent on the delivery region of the country as well as particular zip codes, holiday schedules, weather, UPS overall traffic volume and many other factors completely out of our control. Packages can also get lost or damaged resulting in delays. eBay Payments is the preferred payment method.*All orders are Sales Tax exempt EXCEPT New York, USA DO YOU REQUIRE BUYERS TO CANCEL OR RETURN ITEMS WITHIN A SPECIFIC TIME PERIOD? Cancellations for 100% refund must be made prior to shipping. For customer satisfaction we ship same day on orders before 2pm or next day for orders after 2pm EST. So cancellations must be immediate if the order was a mistake. Cancellation requests sent to us directly via eBay Once shipped we will take pre-authorized returns on unopened shipments for up to 30 days after the order date only if returned in resalable condition, all items are received within 15 days of return authorization and buyer is responsible for all shipping costs. Important: Contact your local code officers prior to purchase if you are going to have inspections since buyer is responsible for all inspection or code issues. If you run into a problem with zoning/code enforcement, the standard return policy, with fees incurred for shipping will apply. So please plan ahead. ARE THERE EXCEPTIONS TO YOUR RETURN OR CANCELLATION POLICIES? If an item arrives damaged, we will replace it right away. Important guidelines must be followed: -Customers must open boxes and inspect completely upon delivery. -Damage must be reported to our office and UPS within 24 hours of shipment being delivered. After 24 hours of receipt of shipment no damage return exceptions apply. This is a UPS insurance policy rule so we have absolutely no flexibility in this matter. We can only file a claim with them within the first 24 hours, so please open your boxes promptly. If damage is reported within the 24 hour window, we will send you a new replacement item, right away.RETURNS FOR WARRANTY ISSUES In case of warranty issues, your items will be repaired or replaced by the manufacturer directly according to their warranty terms and conditions. Please note that after the boxes are opened and/or the items installed, the item is no longer considered "new and resalable" and can not be returned to us. In case of any technical issues the item is now covered under the 2 year manufacturer warranty and rest assured your items will be repaired or replaced by Saniflo directly. The manufacturer is solely liable for any product defects or malfunctions. DO YOU REQUIRE BUYERS TO RETURN ITEMS IN THEIR ORIGINAL SHIPPING CONTAINERS AND/OR PACKAGING? Buyer must return items in original packaging. Items must be received back in original, sellable condition. Be forewarned that it is very hard to return ceramic toilets and tanks unbroken. They are professionally packaged to ship to you with no problem but double shipping is rarely successful. To protect you from this unfortunate case, we urge you: Please purchase shipping insurance on your return shipment for the full value of the items you're returning. If the item is damaged in shipping, we cannot issue a refund, and you would lose the full value of the item. We don't want this to happen to you. That's why insurance through UPS or FedEx is important. It's a very inexpensive way to cover the full value of the shipped item, so there is no risk in shipping your return.WILL YOU OR THE BUYER PAY FOR POSTAGE ON RETURNS? Buyer is responsible for shipping costs on returns. DO YOU CHARGE RESTOCKING OR OTHER FEES? No, a full refund will be given after all shipping and handling charges, which are the responsibility of the buyer. WHAT IF I JUST FOUND OUT THAT THIS WONT WORK FOR MY INSTALLATION OR I CAN'T GET THE CORRECT PERMIT? The same 30 day return policy applies. Please see the full terms above. We strongly urge you to do all of your research and make 100% sure you're ordering the correct pump that will work for your installation, and you get all local permits in advance, as returns are laborious and expensive on this large item. Important Note: The State of Illinois has a very powerful plumbing union that will not approve this product because it costs much less to install and cuts into plumbers profits. While we still sell many units in Illinois, the unit will not pass inspection, if you're planning on getting one.IF I REFUSE THE UPS SHIPMENT, IS THAT THE SAME AS A RETURN? No. If you do not cancel prior to shipping and the unit is shipped, the same policies above apply as returns. Please understand that we cannot simply pay all costs for customers to change their minds since some shipping costs are over $100 one way. We would go out of business very quickly.

Price: 1510.08 USD

Location: Salamanca, New York

End Time: 2024-12-07T00:46:40.000Z

Shipping Cost: 0 USD